How to configure WOL (Wake On LAN) on TP-Link SafeStream Router using the new GUI

Configuration Guide
Updated 06-27-2022 06:30:57 AM FAQ view icon223566
This Article Applies to: 

You can use WOL (Wake on LAN) to boot up your PC from a remote place by sending a Magic Packet via the internet.

  • Network Topology

In the diagram below, PC A is connected to the internet via the router. It is required that PC B can wake up PC A by sending a Magic Packet via the internet.

  • Configuration Scheme

Before configuring WOL, you should do the following preparation:

  1. Make sure that the motherboard of PC A supports WOL. In BIOS setup of PC A, enable Power On By PCIE or Wake Up On LAN.
  2. Make sure that the network card of PC A supports WOL. In network card properties configuration of PC A, allow the network card to wake up the PC, forbid the PC to turn off the network card to save power, and enable Wake on Magic Packet.
  3. PC A should be powered off normally and the power supply is normal.
  4. Make sure the WAN port of the router is routable from PC B.

To achieve this requirement, you can configure the router as follows:

  1. Bind MAC and IP Address of PC A
  2. Reserve the IP address for PC A
  3. Configure Virtual Server.

After you complete the configuration, you can use a WOL software to wake up PC A on PC B.

  • Configuration Procedure

Follow the steps below to configure the router.

Step 1 Bind MAC and IP Address of PC A

There are three methods to do IP-MAC binding: bind in the ARP list, bind in ARP scanning result, or add IP-MAC Binding list entry manually.

  • Bind in the ARP List

Choose the menu Firewall > Anti ARP Spoofing > ARP List to load the following page. If the desired entry is in the list, click the corresponding to bind MAC and IP address of PC A.

  • Bind in ARP Scanning Result

Choose the menu Firewall > Anti ARP Spoofing > ARP Scanning to load the following page. In the general section, specify the scanning IP range according to the DHCP address pool. Click Scan. Wait a minute until the scanning is completed.

In the Scanning Result section, click the corresponding to bind MAC and IP address of PC A.

  • Add IP-MAC Binding List Entry Manually

Choose the menu Firewall > Anti ARP Spoofing > IP-MAC Binding to load the following page. In the IP-MAC Binding List section, click to load the following page. Enter the IP address and MAC address of PC A. Enable Export to DHCP Address Reservation. Check Enable for Status. Click OK.

Step 2 Reserve the IP Address for PC A

Choose the menu Network > LAN > Address Reservation to load the following page. Check if the desired IP address is reserved for PC A.

If there is not a desired entry, click to load the following page. Enter the IP address and MAC address of PC A. Enable Export to IP-MAC Binding. Check Enable for Status. Click OK.

Step 3 Configure Virtual Server

Choose the menu Transmission > NAT > Virtual Servers and click to load the following page. Enter a name for the entry. Specify the WAN port according to the network environment. Specify the external port and internal port as 7, which is used to receive Magic Packets. Specify the internal server IP as 192.168.0.100, which is the IP address of PC A. Select the protocol as UDP. Check Enable for Status. Click OK.

After the above configuration, you can now launch a third-party WOL software on PC B and send a Magic Packet to boot up PC A.

Is this faq useful?

Your feedback helps improve this site.

Community

TP-Link Community

Still need help? Search for answers, ask questions, and get help from TP-Link experts and other users around the world.

Visit the Community >

icon

Accessibility Adjustments

icon RESET

Choose the right accessibility profile for you

OFF

Seizure Safe

Eliminates flashes and reduces color

OFF

Cognitive Disability

Assists with reading and focusing

OFF

Vision Impaired

Enhances the website's visuals

OFF

ADHD Friendly

More focus and fewer distractions

Content Adjustments

Adjust Scale

icon
100%
icon

Highlight Title

icon

Highlight Link

icon

Text Magnifier

icon

Readable Font

icon

Align Center

icon

Align Left

icon

Align Right

icon

Color Adjustment

Low Saturate

icon

High Saturate

icon

Dark Contrast

icon

Light Contrast

icon

Set Text Colors

Monochrome

icon

Set Title Colors

High Contrast

icon

Set BackgroundColor

Orientation Adjustments

Muted

icon

Hide Images

icon

Stop Animation

icon

Reading Mask

icon

Highlight Hover

icon

Big Black Cursor

mutedicon

Big White Cursor

icon

Hide Video/Audio

icon

Stop Video

icon

Stop Audio

icon

Hide Animation

icon

Reading Guide

icon

Useful Links

Chat Now